How To Clean A Dab Rig

A dab rig does not require as much cleaning as a bong used to smoke flowers. Cleaning your dab rig on a regular basis, though, will help ensure that it continues to function properly. If you fail to clean your setup, the quality and flavor of your dabs will deteriorate over time. It’s impossible to hit the device if the percolators are clogged.

There are two strictly wrong and two moderately incorrect ways to clean a dab rig. Never torch any component of your equipment, even if it is clogged, to release the oils. Torching your dab rig’s glass may result in a fracture or shattering. You may keep your tastes prominent and your dab rig functioning without damaging your glass by following five simple methods.

Drop Down

A drop-down glass attachment is a proactive approach to avoid having your rig clogged in the first place. It’s a glass tube that resembles an N or Z that extends the nail from the rig and catches oil that would otherwise go past it, also known as “reclaim.”

The greatest feature of a down stem is that the reclaim remains distinct from the water in the rig. So, in times of need when your stash has been used up, you may collect some out with a dab tool and use it immediately. You can also keep your reclaim in its own container until you’re ready to utilize it for something else, such as an edible recipe.

Cleaning A Dab Rig

There are a few things that must be done to clean a dab rig properly. You’ll need hot water, a high-percentage alcohol like moonshine or 99 percent isopropyl alcohol, and Q-tips before you begin. Salt should be used in conjunction with alcohol as an abrasive for reclaiming stuck in difficult-to-reach areas. The alcohol alone, with some shaking, should be sufficient if you cleaned your rig only recently.

1. Empty Dirty Water

The first step in cleaning your dab rig is to ensure it’s empty. If you’ve had water that hasn’t been changed for a long time and there are a few balls of reclaim floating around, it’s time to drain it. After each usage, the water in your dab rig should be replenished. You may go on to the next stage once there is no water left in the rig.

2. Hot Water Rinse

The next step is to use hot water to help loosen the oils. Hot water alone will remove a few chunks of reclaim for you if you haven’t cleaned in a while. The water shouldn’t be boiling, but it should be as hot as your tap gets or even hotter. You may now drain out all of the water and proceed to the following stage.

3. Alcohol Soak

After rinsing off some oil with a hot water wash, it’s time to finish the job with an alcohol soak. If you’re in a hurry, you may microwave a cup of alcohol for about 10 seconds before adding it to your rig. This will remove virtually all oils at once.

When the liquid goes from clear to a darker yellow, check for any remaining oil build-up. If you discover any, give the rig another shake and allow it to dissolve in its own time. If that doesn’t work, move on to step 2 to be sure no oil is lost.

4. Salt & Shake (Optional)

If your rig is really mucky, you may need more than just isopropyl alcohol to make it appear brand new and unused again. A coarse salt as an abrasive will assist remove anything sticking to the walls in a difficult-to-reach location. If only table salt is available, it will also do the job. Add salt and booze to the mix, then shake until all of the oil is removed from the mixture.

5. Rinse Clean

Allow all of the alcohol to evaporate before tearing that squeaky clean dab rig. Then, to make sure no isopropyl residue remains, rinse thoroughly several times. The scent of the alcohol should be undetectable after a few rinses. Now your dab rig will be ready to use and fill.

Cleaning A Dab Nail

If you want to get the most out of your BHO or other extracts, you’ll have to clean more than your dab rig. The easiest way to keep the flavors in your nail is to keep your dab nail and quartz insert clean. Doing so adds length to the heat retention, flavor, and appearance of your nail. A quartz banger is one of the simplest nails to maintain since it only contains a Q-tip and isopropyl alcohol to clean it.

Unless you’re dabbing at high temperatures on a regular basis, any residual oils from your previous dab will remain. Use a Q-tip to collect the oil as soon as you’re finished with a dab. Don’t worry if you forget. Simply heat your nail with a torch for a couple of seconds to loosen the frozen oil.

Then, after using a Q-tip like you would after a dab, go in with one immediately afterward. There may still be some oil on the walls after you’ve used a Q-tip on the oils from your previous dab.

If a dab is left anywhere on the nail, one isopropyl-soaked Q-tip can be used to remove any residual material. Otherwise, if you reheat for a dab again, a ring of oil will rise and burn black. Additional heating and oxidation will be required to burn it completely clean the next time.

We hope you utilize the information to retain hits fresh and enjoyable after reading this article on how to clean a dab rig. Get a glass drop-down if cleaning isn’t your thing. Cleaning your dab rig with hot water after each use also helps to keep things simple.

Laisser un commentaire

Votre adresse courriel ne sera pas publiée.